Alloys Metallurgy
Mostrando 1-12 de 29 artigos, teses e dissertações.
-
1. Characterization of Ti-35Nb alloy surface modified by controlled chemical oxidation for surgical implant applications
ABSTRACT Titanium-Niobium alloys have been studied for biomedical applications due to their satisfactory biocompatibility. In order to improve the long-term implantation, surface modification techniques have been developed to generate suitable topography, roughness, chemical composition, surface energy, etc. Considering this approach, the present work aimed
Matéria (Rio J.). Publicado em: 16/09/2019
-
2. Comparison of Aluminum Based Alloys Reinforced with Intermetallic Developed by Powder Metallurgy and Arc Melting Routes
Abstract In this work, Al-Ti alloys were prepared using metallic powders of Al and Ti via Powder Metallurgy (PM) and Arc Melting (AM) route. Four chemical compositions including pure aluminum were studied. Metallic powders were mixed with three compositions, Al-5Ti, Al-10Ti and Al-10Ti-2SiC. All the compositions were in atomic percentage. In case of PM, samp
Soldag. insp.. Publicado em: 29/08/2019
-
3. Semi-solid Sintering of Ti6Al4V/CoCrMo Composites for Biomedical Applications
A composite of Ti6Al4V reinforced with CoCrMo particles is fabricated by conventional powder metallurgy and semi-solid sintering. Composites are fabricated by mixing 20% wt. of CoCrMo reinforcing particles into the Ti6Al4V matrix. Sintering is studied by dilatometry tests between 1050 and 1130 °C and compact characterization is performed by SEM and XRD. Mic
Mat. Res.. Publicado em: 31/01/2019
-
4. Mechanical characterization of PM aluminum composites by small punch test
ABSTRACT In this work Small Punch Test (SPT) was applied to study the mechanical behavior of ultrafine-grained Al-Al2O3metal matrix composites (MMCs) fabricated in situ via powder metallurgy route (HITEMAL®). Such MMCs show attractive mechanical properties, enhanced creep performance and increased thermal stability at elevated temperatures, not normally ass
Matéria (Rio J.). Publicado em: 19/07/2018
-
5. Microstructural and Electrochemical behaviour of Aluminium Alloy Composites Produced Using Different Sintering Techniques
Present research work analyses the effect of heating modes on the densification, microstructure and mechanical properties of aluminum alloys [65Al-20Cu-15Mn] fabricated through powder metallurgy route. Sintering of compacts using conventional, microwave and spark plasma sintering methods has been carried out at 525°C. From the results, it has been observed
Mat. Res.. Publicado em: 12/03/2018
-
6. Materials Selection of Optimized Titanium Alloys for Aircraft Applications
The aim of the present work was to explore the correlation between the physical metallurgy of titanium alloys and its main attributes to select optimized materials for structural aircraft applications in the landing gear beam. The Ashby's method was employed as the materials selection strategy to consolidate and evaluate the data collected from the current l
Mat. Res.. Publicado em: 19/02/2018
-
7. Study of Ti-7.5Si-22.5B alloys produced by powder metallurgy
Refractory alloys with silicides and borides have been used in high temperature applications because their elevated melting point, good oxidation resistance and high strength-to-weight ratio. The present study approaches the preparation of Ti-7.5Si-22.5B (at.-%) alloys through high-energy ball milling and sintering. The powders and compacts obtained in these
Mat. Res.. Publicado em: 03/06/2014
-
8. Sinterability and microstructure evolution during sintering of ferrous powder mixtures
The present work is focused on ferrous powder metallurgy and presents some results of a development of a suitable masteralloy for use as an additive to iron powder for the production of sintered steels. The masteralloy was produced by melting a powder mixture containing approximately Fe + 20% Ni + 20% Mn + 20% Si + 1% C (wt%), in order to obtain a cast bille
Mat. Res.. Publicado em: 28/05/2013
-
9. Influência da adição de nanopartículas de TiO2 na obtenção de compósitos a base de liga AA2014 fabricada via metalurgia do pó / Influence of the addition of TiO2 nanoparticles in the composites formation based AA2014 alloy manufactured by powder metallurgy
Aluminum matrix composites and its alloys, especially AA2014, are widely used in automotive and aeronautics applications. The properties of this are very influenced by hardening treatment, however its use is limited at temperatures above 150C due to loss of properties caused by the growth of precipitates at this temperature. The addition of a new phase, fine
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 20/06/2012
-
10. Estudo da microestrutura, da textura cristalográfica e da recristalização em chapas obtidas por lingotamento contínuo e semicontínuo da liga de alumínio AA4006. / A study of the microstructure, crystallographic texture, and recrystallization in AA4006 alloy strips produced by twin roll caster and direct chill processes.
A liga de alumínio designada AA4006 é muito utilizada na indústria. É uma liga do sistema Al-Fe-Si, com teores (% em massa) de Si na faixa de 0,8 a 1,2% e Fe entre 0,5 e 0,8%. Apesar de ser bastante utilizada, ela foi pouco estudada. Neste trabalho foi realizado um estudo comparativo da microestrutura e da textura cristalográfica entre chapas da liga AA
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/02/2012
-
11. Occurrence of Defects in Laser Beam Welded Al-Cu-Li Sheets with T-Joint Configuration
Abstract: In the aerospace industry, laser beam welding has been considered as one of the most promising routes among the new manufacturing processes. Substitution of riveting by laser beam welding of aircraft structures has contributed to weight and cost savings. Concurrently, new aluminum alloys have been developed with the addition of lithium with better
J. Aerosp. Technol. Manag.. Publicado em: 2012-12
-
12. Caracterização de ligas magnéticas sinterizadas para aplicação em núcleos de máquinas elétricas rotativas
The purpose of this work is to study the properties of ferromagnetic alloys obtained by Powder Metallurgy to construct cores of Rotary Electric Machines, usually mounted on rolled steel sheets. To perform these activities, iron power and their alloys obtained by a mixture with different percentages of phosphorus (1, 2 and 3%), silicon (1, 3 and 5%) and nicke
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 2012