Experimental Modal Analysis
Mostrando 1-12 de 59 artigos, teses e dissertações.
-
1. An SHM approach using machine learning and statistical indicators extracted from raw dynamic measurements
Abstract Structural Health Monitoring using raw dynamic measurements is the subject of several studies aimed at identifying structural modifications or, more specifically, focused on damage assessment. Traditional damage detection methods associate structural modal deviations to damage. Nevertheless, the process used to determine modal characteristics can in
Lat. Am. j. solids struct.. Publicado em: 14/03/2019
-
2. Analysis of sensor placement in beams for crack identification
Abstract A previous study has shown that the mode shapes of a beam are more sensitive to damage than other vibrational parameters, thus making them better suited for crack identification purposes. However, they have the disadvantage of being more difficult to be measured. To overcome this difficulty, an interesting idea is to monitor changes produced by crac
Lat. Am. j. solids struct.. Publicado em: 29/10/2018
-
3. The dispersion curve applied in guided wave propagation in prismatic rods.
Abstract The early detection of failures in structures is a subject of great interest in engineering; several of these techniques are linked with the elastic wave propagation, using guided waves is one of these alternatives. Several structures of interest in engineering are laminar arrangements; the wave propagation in this type of structures depends not on
Lat. Am. j. solids struct.. Publicado em: 02/07/2018
-
4. Numerical Study of Vibro-Acoustic Responses of Un-Baffled Multi-Layered Composite Structure under Various End Conditions and Experimental Validation
Abstract This article presents the vibro-acoustic modeling and analysis of un-baffled laminated composite flat panels subjected to harmonic point load under various support conditions. The frequency values of the panel are obtained by using simulation model through the commercial finite element package (ANSYS) via batch input technique. Initially, the rate o
Lat. Am. j. solids struct.. Publicado em: 2017-08
-
5. Parametric Modal Study and Optimization of the Floor Pan of a B-Segment Automotive Using a Hybrid Method of Taguchi and a Newly Developed MCDM Model
Abstract The floor pan is an important component that connects the front and rear segments of the automotive underbody structure. Global stiffness and NVH characteristics of BIW are highly dependent to shape, thickness and mass of the body panels and could be evaluated by modal characteristics of these panels. The feeling of solidness and comfort of passenge
Lat. Am. j. solids struct.. Publicado em: 2016-12
-
6. Finite Element Analysis of Structures with Extruded Aluminum Profiles Having Complex Cross Sections
Abstract Extruded aluminum profiles are widely used in building and automation structures due to their durability, lightweight, corrosion resistance, shorter fastening time and reusability. Proper design is crucial in maintaining the lifespan of these structures. It is therefore essential to determine the structural behaviors of the structures such as the na
Lat. Am. j. solids struct.. Publicado em: 2016-08
-
7. Comparison of In-Flight Measured and Computed Aeroelastic Damping: Modal Identification Procedures and Modeling Approaches
ABSTRACT The Operational Modal Analysis technique is a methodology very often applied for the identification of dynamic systems when the input signal is unknown. The applied methodology is based on a technique to estimate the Frequency Response Functions and extract the modal parameters using only the structural dynamic response data, without assuming the kn
J. Aerosp. Technol. Manag.. Publicado em: 2016-06
-
8. Effects of material properties on generation of brake squeal noise using finite element method
AbstractThis research paper is concerned with the disc brake squeal problem for passenger cars. The aim of the present research is developing a finite element model of the disc brake assembly in order to improve understanding of the influence of Young's modulus on squeal generation. A detailed finite element model of the whole disc brake assembly that integr
Lat. Am. j. solids struct.. Publicado em: 2015-08
-
9. Mechanical properties of nanocomposite laminated structure and its sensibility to modal analysis procedure
In this work, tensile and shear modulus, as well as Poisson's ratio of a woven orthotropic nanocomposite plate were determined from vibration data. Plates used in the experiment were 16 layers S2-glass/epoxy composite manufactured by vacuum assisted wet layup. The nanocomposite plate was obtained by adding 0%, 1%, 2%, 5% and 10% nanoclays in weight to the ep
Lat. Am. j. solids struct.. Publicado em: 2014-03
-
10. Finite element analysis of high modal dynamic responses of a composite floor subjected to human motion under passive live load
Light weight and long span composite floors are common place in modern construction. A critical consequence of this application is undesired vibration which may cause excessive discomfort to occupants. This work investigates the composite floor vibration behavior of an existing building based on a comprehensive study of high modal dynamic responses, the rang
Lat. Am. j. solids struct.. Publicado em: 2013-05
-
11. Structure-borne transmissibility evaluation through modeling and analysis of aircraft vibration dampers
Abstract In the aircraft industry a great practical relevance is given to the extensive use of vibration dampers between fuselage and interior panels. The proper representation of these isolators in computer models is of vital importance for the accurate evaluation of the vibration transmission paths for interior noise prediction. In general, simplified mode
J. Aerosp. Technol. Manag.. Publicado em: 2011-08
-
12. AvaliaÃÃo da intenÃÃo de realizar mamografia como subsÃdio para aÃÃes na promoÃÃo da saÃde / Intention assessment to perform mammography as support to actions to the health promotion
Recognizing the magnitude of the public health problem that breast cancer has become over the years and considering mammography as specific procedure for early detection, mammography screening was elected as desired behavior for this investigation. The aim was to assess the behavioral intention and its determinants to perform mammography screening among wome
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/03/2010