Inverse Modeling
Mostrando 1-12 de 52 artigos, teses e dissertações.
-
1. Uma abordagem experimental e numérica para determinação de curvas de compressão para concreto simples e reforçados com fibras de aço
RESUMO A curva tensão-deformação do concreto é importante para o dimensionamento de estruturas, pois por meio dela é possível obter sua resistência à compressão, sua deformação de pico, o módulo de elasticidade e a tenacidade do concreto. Entretanto, essa é uma propriedade que não é comumente determinada nos ensaios de controle de qualidade do
Matéria (Rio J.). Publicado em: 16/09/2019
-
2. Hydrostatic Equilibrium between Soil Samples and Pressure Plates Used in Soil Water Retention Determination: Consequences of a Questionable Assumption
ABSTRACT Soil water retention is among the soil hydraulic properties most routinely measured in studies of soil physics and related areas. This property is used in dynamic simulations of vadose zone processes such as soil water availability, surface boundary processes of evaporation and infiltration, and the fate of soil pollutants. The most common measureme
Rev. Bras. Ciênc. Solo. Publicado em: 29/07/2019
-
3. Actual evapotranspiration and crop coefficient of sweet orange during the initial development phase in the Rio Largo region, Alagoas
RESUMO: A determinação da evapotranspiração real da cultura (ETa) é importante para o manejo da irrigação. Os principais métodos e modelos físicos de estimativa da ETa requerem dados que não são facilmente disponíveis. Neste trabalho, obteve-se o coeficiente da cultura (Kc) da laranja lima na fase inicial de desenvolvimento e avaliou-se o desemp
Cienc. Rural. Publicado em: 30/05/2019
-
4. DAIRY PRODUCTION OF ‘SAANEN’ GOATS BASED ON METEOROLOGICAL VARIABLES AND FUTURE CLIMATE SCENARIOS
ABSTRACT This study aimed to modeling and bioclimatic zoning of ‘Saanen’ goat milk production in northeastern Brazil. Data were obtained from a 14-year dairy control program for 246 ‘Saanen’ goat matrices. Dairy production meteorological influence and mathematical modeling were assessed through statistical analyses such as Pearson’s correlation mat
Eng. Agríc.. Publicado em: 2017-04
-
5. Finite Element Modeling and Experimental Verification of Nitriding Process in S30C Steel
A mathematical model has been developed to simulate the nitriding process of plain carbon steel, considering the simultaneous diffusion of nitrogen in different iron-nitrogen (Fe-N) phases and the precipitation dynamics of γ' and ε iron-nitride. The model can predict the distribution of nitrogen concentration, volume fraction of Fe-N phases and hardness. F
Mat. Res.. Publicado em: 16/02/2017
-
6. Modeling the reflection of Photosynthetically active radiation in a monodominant floodable forest in the Pantanal of Mato Grosso State using multivariate statistics and neural networks
ABSTRACT The study of radiation entrance and exit dynamics and energy consumption in a system is important for understanding the environmental processes that rule the biosphere-atmosphere interactions of all ecosystems. This study provides an analysis of the interaction of energy in the form of photosynthetically active radiation (PAR) in the Pantanal, a Bra
An. Acad. Bras. Ciênc.. Publicado em: 15/08/2016
-
7. Numeric reconstruction of 2D cellular actomyosin network from substrate displacement
Introduction: One of the fundamental structural elements of the cell is the cytoskeleton. Along with myosin, actin microfilaments are responsible for cellular contractions, and their organization may be related to pathological changes in myocardial tissue. Due to the complexity of factors involved, numerical modeling of the cytoskeleton has the potential to
Res. Biomed. Eng.. Publicado em: 27/11/2015
-
8. Preliminary analysis of knee stress in Full Extension Landing
OBJECTIVE: This study provides an experimental and finite element analysis of knee-joint structure during extended-knee landing based on the extracted impact force, and it numerically identifies the contact pressure, stress distribution and possibility of bone-to-bone contact when a subject lands from a safe height. METHODS: The impact time and loads were
Clinics. Publicado em: 2013-09
-
9. Modelagem e avaliação comparativa dos métodos Luus-Jaakola e R2W aplicados na estimativa de parâmetros cinéticos de adsorção / Modeling and comparative evaluation of Luus-Jaakola and R2W methods applied in estimating kinetic parameters of adsorption
As técnicas inversas têm sido usadas na determinação de parâmetros importantes envolvidos na concepção e desempenho de muitos processos industriais. A aplicação de métodos estocásticos tem aumentado nos últimos anos, demonstrando seu potencial no estudo e análise dos diferentes sistemas em aplicações de engenharia. As rotinas estocásticas sã
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 18/06/2012
-
10. Evaluation of radiances generated by solving the radiative-transfer equation with different approaches
Radiative transfer is the main phenomenon in the basis of several relevant problems of scientific and technological interest. Examples of application of the mathematical and computational modeling of such phenomenon can be found in astronomy, environmental sciences, engineering and medicine among many different areas. The integro-differential equation known
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2012-06
-
11. Aplicação do LIDAR no inventário de florestas plantadas / Lidar application in planted forest inventory
LIDAR (Light Detection and Ranging) has become an efficient tool for data extraction in forest inventory and other forest related studies. This works objective was to establish an efficient methodology for the use of this technology with the goal of counting the number of stems in a Eucalyptus plantation in South Bahia, Brazil, from the processing of raw dat
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 05/08/2011
-
12. Oil-water liquid flow rate determined from measured pressure drop and water hold-up in horizontal pipes
Stimulated by rapid progress in down-hole measuring techniques production engineers wonder whether in the near-future monitoring of oil/water production rates for horizontal wells can become possible on the basis of measured oil/water pressure losses and water hold-ups. A complicating issue is that these measured data depend on the oil and water flow pattern
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2011