Lubricity
Mostrando 1-12 de 14 artigos, teses e dissertações.
-
1. Ureteral access sheaths: a comprehensive comparison of physical and mechanical properties
ABSTRACT Introduction: Ureteral access sheaths (UAS) facilitate flexible ureteroscopy in the treat- ment of urolithiasis. The physical properties of UAS vary by manufacturer and model. We compared three new UAS: Glideway (GW, Terumo, 11/13Fr, 12/14Fr), Pathway (PW, Terumo 12/14F) and Navigator HD (NHD, Boston Scientific, 11/13Fr, 12/14Fr) in the domains of
Int. braz j urol.. Publicado em: 2018-06
-
2. Evaluation of Lubricating Properties of Diesel Based Fuels Micro Emulsified With Glycerin
The mineral diesel oil sold in Brazil, due to environmental reasons; presents sulfur concentration of 10 ppm, which causes a deficiency of lubricity, since sulfur is one of the chemical species that gives a good lubricating characteristic. Poor lubricity affects performance and causes failure of engine parts. This study aimed to evaluate the use of glycerin
Mat. Res.. Publicado em: 18/12/2017
-
3. The Lubricity Analysis of Cutting Fluid Emulsions
The new generation of cutting fluids should have some characteristics, such as low toxicity and biodegradability. A bio-cutting fluid emulsion are an excellent option because they present those properties, as well as good mechanical performance. The present study aims to investigate the lubricity of O/W emulsions (cutting fluid emulsion), varying the concent
Mat. Res.. Publicado em: 2017
-
4. Correlation Between Fuel Lubricity and Vibration Signals Obtained in Ball-disc Analysis Using Fourier Transform
During the contact between metallic surfaces in mechanical systems, some dynamic characteristics present significant changes as the vibration signal patterns. The acquisition and characterization of these signals, by the use of Fourier Transform (FT), are non-intrusive tools in the evaluation of lubricity. This study aimed to evaluate dynamically the fuels l
Mat. Res.. Publicado em: 24/11/2015
-
5. Effect of desulfurization of diesel and its blends with biodiesel on metallic contact
The current environmental scenario has required changes in fuel nature, in order to minimize the harmful effects caused by sulfur in diesel. However, reductions in sulfur content promote loss of its lubricity and consequently wear in the injection system of the diesel engine. This study aimed to investigate the influence of sulfur minimization on fuel lubric
Mat. Res.. Publicado em: 22/07/2014
-
6. Micro and nanometric wear evaluation of metal discs used on determination of biodiesel fuel lubricity
The contact of diesel fuel with engine subsystems demands a good wear resistance. Lubricity is an important feature for integrity of injection system and the sulphur composites are primarily responsible for lubrication of the injector nozzle. Biodiesel is responsible for partially restoring the lubricity of diesel fuel that presents low levels of sulphur com
Mat. Res.. Publicado em: 04/07/2014
-
7. Antiwear and antioxidant studies of cardanol phosphate ester additives
In the search for new applications and products derived from Cashew Nut Shell Liquid (CNSL), we report herein the synthesis and characterization (GC/MS and ¹H, 13C, and 31P NMR) of four phosphate esters derived from hydrogenated cardanol, including their applications as antiwear additives for diesel (S500) and as antioxidant additives for mineral oils, eval
Braz. J. Chem. Eng.. Publicado em: 2012-09
-
8. Efeitos do tratamento ácido no inóculo sobre a produção e massa molar do ácido hialurônico / Effects of the acid stress in the inoculum on the production and molecular weight of hyaluronic acid
Hyaluronic acid (HA) is a polysaccharide composed of 2000-25000 disaccaridic units of glucuronic acid and N-acetylglucosamine ?-bonds formed by 1-3 and 1-4 ?-turn. Due its physicochemical properties such as lubricity, hydrophilic and biocompatible, HA has been widely applied in the medical field. Many Studies show that production of HA by fermentation microb
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 21/10/2011
-
9. Estudo do comportamento PVT de misturas de metano e fluidos de perfuração base éster / Study of the PVT behavior of methane and ester based drilling fluids mixtures
During conventional drilling operations, it is necessary to maintain the wellbore pressure greater than the reservoir pore pressure, otherwise a kick may occur. If the well control procedure is not effective during the circulation of the formation influx out of the well, a blowout could happen, which is a dangerous event concerning safety and environmental i
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 22/06/2010
-
10. Application of experimental design in different stages of the oil refining / Aplicação de planejamento de experimentos em diferentes etapas do refino de petroleo
In this work, experimental design technique was applied to different optimization studies, which were carried out in the Paulínia Refinery (Replan). The work covers applications of the technique in laboratorial scale, in computational tool, and the use of the technique in different industrial plants. The laboratory studies consisted in the evaluation of the
Publicado em: 2009
-
11. Evaluation of the Fluid Dynamic Properties and Kinetic Study by Pressurized Differential Scanning Calorimetry (PDSC) of Ethanolic Biodiesel Derived from Used Frying Oil / Avaliação das Propriedades Fluído-dinâmicas e Estudo Cinético por Calorimetria Exploratória Diferencial Pressurizada (PDSC) de Biodiesel Etílico Derivado de óleo de fritura usado
The present work aimed at investigating the biodiesel issuing from the transesterification of used frying oil with ethanol, via alkaline catalysis. Such investigation covers its thermo-oxidative stability during heating (thermal analysis and rheological properties) as well the kinetic profiles of the samples in the best oxidative induction time by the techni
Publicado em: 2009
-
12. Coolant lubricity and coolant-lube compatibility with regard to slideway behavior
Coolants are widely used in industries for metal cutting operations. Though there are varieties of coolants available, the most widely used are water-soluble coolants because of their low cost and better heat dissipation compared to straight cutting oils. In the present investigation, amongst the various causes, which deteriorate the coolant, the role of har
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2008-12