Sintering Process
Mostrando 1-12 de 99 artigos, teses e dissertações.
-
1. A review on the ceramic additive manufacturing technologies and availability of equipment and materials
Abstract Ceramic additive manufacturing allows the fabrication of small series of complex parts without the high costs of molds usually associated with traditional ceramic processing. Although research into ceramic 3D printing by all technologies started back in the 90s, its industrial application is still quite restricted when compared to polymers and metal
Cerâmica. Publicado em: 2022
-
2. Obtainment of a new metal matrix composite from the recycling of UNS S31803 duplex stainless steel by powder metallurgy
Abstract The purpose of circular economy is to maximize resources efficiency. With the increase in consumption of raw materials, energy and waste generation, recycling is necessary for environmental and industrial reasons. Thus, the powder metallurgy, together with mechanical milling, stands as a new method for scraps recycling. This study aimed to produce U
REM - International Engineering Journal. Publicado em: 2022
-
3. Sintering mechanisms of partially stabilized zirconia (TZ3Y) with ZnO and Co3O4 as sintering additives
Abstract In this work, the sintering mechanisms of 3 mol% yttria-stabilized zirconia (TZ3Y) and TZ3Y containing 0.3 wt% of ZnO or Co3O4 were analyzed by determining the apparent activation energy of sintering from dilatometry data and observing the evolution of microstructure. Dilatometry test was performed at a heating rate ranging from 5 to 20 °C/min from
Cerâmica. Publicado em: 2021-06
-
4. Cold sintering and electric characterization of ZnO-BaTiO3 composites
Abstract The sintering is an essential step in the processing of ceramics materials. A number of researchers have reported new techniques for sintering. However, in general, the process still demands high temperatures. This paper reports the results of the cold sintering of ZnO-BaTiO3 composites. The microstructural, structural, and electric properties of th
Cerâmica. Publicado em: 2021-03
-
5. Unified comprehension of the kinetics of isothermal ceramic processes under field-free and resonant wave-field conditions
Abstract This paper proposes a unified comprehension of the isothermal ceramic process kinetics stemming from mesoscopic irreversible thermodynamics. Accordingly, a unified process kinetic equation (UPKE) is derived, which predicts that the global isothermal process rate of any ceramic process is, in general, nonlinearly related both to its activation energy
Cerâmica. Publicado em: 2021-03
-
6. Preparation and characterization of yttria stabilized zirconia (YSZ) films deposited by dip-coating on LSM-YSZ substrate with different proportions
ABSTRACT In this work, sol-gel/dip-coating process for obtaining yttria stabilized zirconia (YSZ, ZrO2–8% Y2O3) films deposited onto LSM-YSZ (lanthanum strontium manganite (LSM, La0.7Sr0.3MnO3) mixed with YSZ) with different proportions (20/80, 50/50, 80/20) was investigated. The films were deposited on substrate varying the number of layers deposited. LSM
Matéria (Rio J.). Publicado em: 25/11/2019
-
7. Additive manufacturing of titanium alloy could modify the pathogenic microbial profile: an in vitro study
Abstract Additive manufacturing (AM) is an emerging process for biomaterials and medical devices. Direct Laser Metal Sintering (DLMS) is an AM technique used to fabricate Ti–6Al–4V implant materials with enhanced surface-related properties compared with wrought samples; thus, this technique could influence microbial adsorption and colonization. Therefore
Braz. oral res.. Publicado em: 30/09/2019
-
8. Comparison of Aluminum Based Alloys Reinforced with Intermetallic Developed by Powder Metallurgy and Arc Melting Routes
Abstract In this work, Al-Ti alloys were prepared using metallic powders of Al and Ti via Powder Metallurgy (PM) and Arc Melting (AM) route. Four chemical compositions including pure aluminum were studied. Metallic powders were mixed with three compositions, Al-5Ti, Al-10Ti and Al-10Ti-2SiC. All the compositions were in atomic percentage. In case of PM, samp
Soldag. insp.. Publicado em: 29/08/2019
-
9. Analysis of the densification of a composite obtained by sintering process of aluminum bronze powders with different carbides
Abstract Aluminum bronze alloy is applied in environments that require materials of high mechanical resistance and wear, such as marine, oil & gas and aerospace ones. This study analyzes the densification of composites based on aluminum bronze with additions of the vanadium (VC) and niobium (NbC) carbides, and the influence of these carbides in the milling e
REM, Int. Eng. J.. Publicado em: 19/06/2019
-
10. Objective criterion for evaluation of the quality decoration in ceramic floor tile production prior to the sintering process
Abstract In the ceramic tile decoration process, the set of variables that can cause hue variation is quite wide and independent of the methodology used in the production. The understanding of the effects of these variables over the final expected result is of great importance to the producers, especially if it could be done before the ceramic tile’s sinte
Cerâmica. Publicado em: 2019-01
-
11. Controlling sintering and grain growth of nanoceramics
Resumo Sinterização e crescimento de grão são processos fundamentais que afetam a evolução microestrutural das cerâmicas. Os modelos fenomenológicos que descrevem esses processos, conforme encontrados nos livros didáticos, são simplificações do conjunto altamente dinâmico de parâmetros do sistema, o que leva à previsibilidade limitada e à nec
Cerâmica. Publicado em: 2019-01
-
12. Development of a microwave absorbing material based on molybdenum-doped niobium pentoxide
Abstract This work aimed to perform the characterization of electrical properties of niobium pentoxide, Nb2O5, pure and doped with molybdenum, prepared by powder metallurgy route and to do a comparative analysis of the influence of this material when sintered in a muffle or in a microwave oven. The results showed that the doping of the niobium pentoxide with
Cerâmica. Publicado em: 2019-01