Sliding Mechanics
Mostrando 1-12 de 14 artigos, teses e dissertações.
-
1. Physical and chemical properties of orthodontic brackets after 12 and 24 months: in situ study
Objective: The aim of this article was to assess how intraoral biodegradation influenced the surface characteristics and friction levels of metallic brackets used during 12 and 24 months of orthodontic treatment and also to compare the static friction generated in these brackets with four different methods of the ligation of orthodontic wires. Material an
J. Appl. Oral Sci.. Publicado em: 2014-06
-
2. Evaluation of the friction force generated by monocristalyne and policristalyne ceramic brackets in sliding mechanics
OBJETIVO: avaliar e comparar in vitro as cargas máximas de atrito geradas por três tipos de braquetes estéticos, sendo dois deles cerâmicos policristalinos convencionais (20/40 e InVu) e um monocristalino de safira (Radiance), em ambientes seco e umedecido por saliva artificial. Também avaliar a influência exercida pela saliva artificial sobre as carga
Dental Press J. Orthod.. Publicado em: 2013-02
-
3. The role of friction in orthodontics
INTRODUCTION: Sliding mechanics is widely used during orthodontic treatment. One of the disadvantages of this mechanics is the friction generated at the bracket/archwire interface, which may reduce the amount of desired orthodontic movement obtained. Due to the application and great acceptance of this type of mechanics, the role of friction in Orthodontics h
Dental Press Journal of Orthodontics. Publicado em: 2012-04
-
4. Avaliação das distribuições de tensões, por meio da análise de elementos finitos, em uma hemi-maxila, durante a fase de retração anterior por deslizamento, na mecânica ortodôntica / Evaluation of the tensions distributions, using the finite element analysis, in an hemi-maxilla during a sliding anterior retraction , in an orthodontic mechanics
O objetivo deste estudo foi analisar, por meio do método dos elementos finitos, como ocorreram as distribuições de tensões nos dentes, osso e aparelho ortodôntico, durante a fase de retração por deslizamento (150g), em um caso com extrações. Simularam-se duas posições do gancho (mesial e distal de canino), duas alturas do gancho (4 e 9mm) e duas a
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 15/04/2011
-
5. Applied mechanics of the Puricelli osteotomy : a linear elastic analysis with the finite element method
Background: Surgical orthopedic treatment of the mandible depends on the development of techniques resulting in adequate healing processes. In a new technical and conceptual alternative recently introduced by Puricelli, osteotomy is performed in a more distal region, next to the mental foramen. The method results in an increased area of bone contact, resulti
Publicado em: 2010
-
6. COMPARAÇÃO DO ATRITO IN VITRO EM BRAQUETES ESTÉTICOS CONVENCIONAIS E AUTOLIGADOS / A comparison of in vitro friction forces among conventional and self-ligating aesthetic orthodontic brackets
The aim of this in vitro study was to compare the friction resistances among conventional steel-ligated and self-ligating aesthetic brackets with different retangular stainless steel archwires sizes at zero and three degrees angulation. 120 brackets of 6 commercial brands (Gemini, Clarity conventional, Transcend, Inspire, Clarity self-ligating, Damon self-li
Publicado em: 2009
-
7. Food mechanics: a new device for testing fruits and vegetables
The new mechanical device developed is capable of performing compression tests but also bending, torsion and tensile tests. Its measurement system has the following components: a load cell (0 to 9800 N), a strain gauge signal conditioning board, a plug-in general purpose data acquisition board, and a displacement sensor (0 to 29.7 mm). These components are c
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2007-03
-
8. ANÁLISE COMPARATIVA DOS NÍVEIS DE ATRITO EM BRÁQUETES CONVENCIONAIS E AUTOLIGADOS / Friction levels comparative analysis in self-ligated and conventional brackets.
The friction between brackets and orthodontic wires is an important issue to be considered concerning to orthodontic treatment efficiency in the sliding mechanics. Because this, always there are a search for ways to reduce the friction levels during this type of mechanics. With the introduction of self-ligated bracketts, it was observed that one of these dev
Publicado em: 2007
-
9. Simulação da interação casco-propulsor de uma embarcação usando mecânica dos fluidos computacional (CFD). / Simulation of the propeller-hull interaction using computational fluid mechanics (CFD).
Este trabalho discute a questão da interação entre o casco do navio e o propulsor em funcionamento conjunto, e sua simulação por ferramentas computacionais. O texto se concentra em descrever os principais efeitos dessa interação, as principais dificuldades em se estimar esses efeitos, os métodos tradicionalmente usados, e como ferramentas computacion
Publicado em: 2007
-
10. Contribuição ao emprego da mecânica do dano para a análise do comportamento dinâmico não-linear de vigas em concreto armado / Contribution to the application of damage mechanics in non-linear dynamic behaviour analysis of reinforced concrete beams
O trabalho trata da formulação e implementação numérica de um modelo de dano para o concreto. O objetivo é o de reproduzir laços de histerese observados experimentalmente em diagramas de tensão-deformação uniaxiais quando, a partir de um certo nível de solicitação, e dano correspondente, passam-se a realizar ciclos de descarregamento e recarrega
Publicado em: 2003
-
11. On the theory of muscle contraction: filament extensibility and the development of isometric force and stiffness.
The newly discovered extensibility of actin and myosin filaments challenges the foundation of the theory of muscle mechanics. We have reformulated A. F. Huxley's sliding filament theory to explicitly take into account filament extensibility. During isometric force development, growing cross-bridge tractions transfer loads locally between filaments, causing t
-
12. A monoclonal antibody against the dynein IC1 peptide of sea urchin spermatozoa inhibits the motility of sea urchin, dinoflagellate, and human flagellar axonemes.
To investigate the role of axonemal components in the mechanics and regulation of flagellar movement, we have generated a series of monoclonal antibodies (mAb) against sea urchin (Lytechinus pictus) sperm axonemal proteins, selected for their ability to inhibit the motility of demembranated sperm models. One of these antibodies, mAb D1, recognizes an antigen