Steel Aisi D6
Mostrando 1-12 de 13 artigos, teses e dissertações.
-
1. Analysis of the Dynamic Stability of Ball-End Milling of AISI D6 Hardened Steel
AISI D6 hardened steel is a difficult to cut material that it is employed in mould and die manufacturing where long ball-end mills are frequently required to machine deep cavities. This condition can lead to excessive vibration between tool and workpiece resulting in a poor surface finishing and reduced tool life. This work analyses the dynamic stability of
Mat. Res.. Publicado em: 02/12/2019
-
2. EXPERIMENTAL AND THEORETICAL ANALYSIS OF NA OXAZINOQUINOXALINE DERIVATIVE FOR CORROSION INHIBITION OF AISI 1018 STEEL
The inhibitory ability of an oxazinoquinoxaline derivative (OAQX) against the corrosion of AISI 1018 mild steel induced by aqueous 0.6 mol L-1 NaCl solution is herein evaluated. Linear polarization resistance studies showed the inhibitory efficiency of OAQX varying from 62.75% to 75.93% with OAQX concentration ranged from 0.259 x 10-4 mol L-1 to 3.243 x 10-4
Quím. Nova. Publicado em: 2018-03
-
3. INIBIÇÃO À CORROSÃO DE AÇO-CARBONO EM MEIO SALINO PELO HETEROCICLO ISATINA VEICULADO EM MICROEMULSÕES
Polar microemulsion systems (SME) based on saponified coconut oil (OCS) as surfactant were prepared in order to increase the solubility of the heterocycle isatin (IST) aiming at its application as corrosion inhibitor against AISI 1020 mild steel, in saline medium. The adsorptions phenomena of the tested SME systems (SME-OCS1-IST and SME-OCS2-IST) in the liqu
Quím. Nova. Publicado em: 2017-08
-
4. Synthesis of Vanadium Interface for HFCVD Diamond Deposition on Steel Surface
Laser cladding of vanadium carbide powder developed an interlayer on AISI D6 steel as a diffusional barrier and to relief thermal residual stress. Laser cladding experiments varied resolution (DPI) and scanning speed (mm/s). CVD diamond deposition on this interface went on by HFCVD technique. The coatings were characterized by X-ray diffraction analysis (XRD
Mat. Res.. Publicado em: 06/07/2017
-
5. Investigating the correlation between some of the properties of plasma nitrided AISI 316L stainless steel
When AISI 316L stainless steels are submitted to the nitriding process at temperatures lower than 450 °C, a high nitrogen content expanded austenite phase is formed, which shows higher hardness and higher pitting corrosion resistance compared to the untreated material. As a result, this material becomes adequate for biomedical application. The conditions of
Mat. Res.. Publicado em: 28/05/2013
-
6. Agentes inibidores da atividade metabólica e do processo de adesão de Desulfotomaculum nigrificans em superfície de aço inoxidável / Agents of inhibition of the metabolic activity and of the process of adhesion of Desulfotomaculum nigrificans in surface of stainless steel
As bactérias redutoras de sulfato (BRS) são consideradas o principal grupo de microrganismos envolvidos na formação de biofilmes e biocorrosão de oleodutos. A prevenção e o controle do crescimento desse grupo bacteriano têm sido realizados principalmente pela utilização de agentes biocidas ou bacteriostáticos, bem como pelo uso de inibidores metab
Publicado em: 2009
-
7. Ruido Barkhausen y emisión magneto acústica para la caracterización de materiales ferromagnéticos
The techniques of Barkhausen Noise (BN) and Magneto Acoustic Emission (MAE) were applied to a ferromagnetic material with the objective of correlating the obtained signals with the micro structural changes. The first step was the development of an Integral Measurement System (IMS) for the BN and MAE signals. Different devices as magnetic yoke, current source
Matéria (Rio de Janeiro). Publicado em: 2008-03
-
8. Avaliação do desempenho do aço D6 tratado termicamente e netretado em plasma com gaiola catódica visando aplicação industrial
In this research there was an evaluation of the best conditions of nitriding in plasma within a cathodic cage at an atmosphere of 80% N2-20%H2 in samples of tool manganese steel AISI D6, cold working, treated thermally in the following conditions: tension relief, treated thermally to temperature of maximum heat, temperate heat and temperate and temperate hea
Publicado em: 2008
-
9. Avaliação da Tenacidade à Fratura e da Resistência à Fadiga de Dois Aços Utilizados em Eixos de Carros Torpedos
Fatigue and fracture of railway shafts are technical problems that have been treated in studies of mechanical behavior of materials. The pugh car shafts fracture during operation causes production losses and high cost to replace them. In this work, it has been studied the fracture toughness through CTOD parameter and the fatigue crack growth da / dNxΔK
Publicado em: 2008
-
10. Surface and interface of micro and nanostructured silicon films deposited on AISI D6 tool steel substrates by EB-PVD / Superfície e interface em filmes micro e nanoestruturados de silício depositadas por PVD em substratos de aço ferramenta D6
Neste trabalho é proposta a obtenção de filmes de silício aderentes às superfícies de substratos de aço-ferramenta AISI D6 e a caracterização de suas superfícies e interface filme-substrato. Os filmes de silício foram depositados nas superfícies polidas dos substratos metálicos por deposição física via fase vapor com vaporização do silício
Publicado em: 2007
-
11. Surface modification study of took and high speed steel with functional and adherent TiN and ain films obtained by PVD reactive deposition / Estudo das modificações de superfícies de aços ferramenta e aços rápido com filmes funcionais e aderentes de TiN e de ain obtidos via deposição reativa por PVD
As aplicações tecnológicas atuais de materiais são vastas, principalmente metais revestidos com filmes de nitretos. Nos últimos anos, muitas investigações tem sido realizadas com o objetivo de otimizar a aderência destes filmes em substratos de aços visando ampliar o seu campo de aplicações. Os filmes de nitretos compostos de cátions metálicos,
Publicado em: 2005
-
12. Estudo das modificações de superfícies de aços ferramenta e aços rápido com filmes funcionais e aderentes de TiN e de ain obtidos via deposição reativa por PVD / Surface modification study of took and high speed steel with functional and adherent TiN and ain films obtained by PVD reactive deposition
As aplicações tecnológicas atuais de materiais são vastas, principalmente metais revestidos com filmes de nitretos. Nos últimos anos, muitas investigações tem sido realizadas com o objetivo de otimizar a aderência destes filmes em substratos de aços visando ampliar o seu campo de aplicações. Os filmes de nitretos compostos de cátions metálicos,
Publicado em: 2005