Steel Frame
Mostrando 1-12 de 36 artigos, teses e dissertações.
-
1. Effect of Rolling Reduction and Temperature on the Oxide Scale of Hot Rolled Mild Steel Strip
Hot rolling experiments were designed to investigate the effect of rolling temperature and rolling deformation on microstructure, thickness and surface red scale of hot rolled mild steel oxide scale by spectrometer, SEM and pickling experiment. The research results show that in the same other experiment conditions, the greater the rolling deformation, the th
Mat. Res.. Publicado em: 04/11/2019
-
2. Seismic Upgrading of Exterior Reinforced Concrete Frame with Small Column and Joint Area Using Externally Attached Steel Column
Abstract This paper presents cyclic load test of five exterior reinforced concrete frames. All the specimens represent a substandard single-span, low-rise reinforced concrete frame building which behaves a weak column-strong beam mechanism under a strong seismic loading. The first three exterior frames M1, M2 and M3 were designed for the joint shear critical
Lat. Am. j. solids struct.. Publicado em: 10/07/2019
-
3. Inelastic second-order analysis of steel columns under minor-axis bending
Abstract The inelastic second-order behavior of steel structural columns under minor-axis bending is presented in this article. To study this behavior, a nonlinear frame element formulation is adopted in which the steel's plasticity process is accompanied at the nodal points of each finite element through the refined plastic-hinge method (RPHM). A tangent mo
REM, Int. Eng. J.. Publicado em: 19/06/2019
-
4. Análise Acústica de Fachadas de Light Steel Frame e Placas Cimentícias
RESUMO A construção a seco tem sido considerada uma alternativa tecnológica aos sistemas construtivos convencionais e, no Brasil, sistemas como o Light Steel Frame e Drywall passaram a ser empregados em maior escala nos últimos anos. Basicamente, estes sistemas consistem em painéis estruturados por perfis de aço, preenchidos internamente por uma lã de
Matéria (Rio J.). Publicado em: 10/06/2019
-
5. Vida a fatiga de uniones soldadas mediante PAW de aceros microaleados al boro
ABSTRACT In the last years microalloyed boron steels have been adopted in the automotive industry to achieve weight reductions. Namely, they are used as load-bearing elements such as pillars and reinforcements, in a quenched and tempered (QT) condition with tensile strength ranging from 800 to 1300 MPa. Dual-Phase (DP) steels have also been introduced in thi
Matéria (Rio J.). Publicado em: 19/07/2018
-
6. On the Nonlinear Transient Analysis of Planar Steel Frames with Semi-Rigid Connections: From Fundamentals to Algorithms and Numerical Studies
Abstract This paper presents the fundamentals for prediction of a more realistic behavior of planar steel frames with semi-rigid connections under dynamic loading. The majority of the research in this area concentrates on the nonlinear static analysis of frames with semi-rigid connections. Indeed, few studies have contributed to the nonlinear dynamic and vi
Lat. Am. j. solids struct.. Publicado em: 03/05/2018
-
7. Three-level performance-based optimization method of steel frames
Abstract This paper describes a three-level performance-based optimization model and an estimate method of residual top displacement for steel frames at three earthquake levels. The steel frames are supposed to be elastic at frequent earthquake, inelastic and hardening at occasional and rare earthquakes, respectively. The estimate formula is derived and est
Lat. Am. j. solids struct.. Publicado em: 23/04/2018
-
8. Comparison of Developed Numerical Macro and Micro Masonry Models for Static and Dynamic Analysis of Masonry-infilled Steel Frames
Abstract First, the basic characteristics of macro and micro masonry models in numerical analyses of masonry structures are discussed. Afterwards, developed numerical macro and micro masonry models, intended for the nonlinear static and dynamic analysis of unreinforced and confined masonry walls, as well as of masonry-infilled frames, are briefly presented.
Lat. Am. j. solids struct.. Publicado em: 2016-12
-
9. A stochastic approach for the wind load effect on steel structures
Abstract The Brazilian design load standard still provides a wind speed map developed in 1977. Since then, new data have been collected and new charts have been proposed in literature. The literature not only alerts to changes in short-term wind gust patterns, but it also warns that the wind speed values are higher than observed in the past. Many researchers
Rem: Rev. Esc. Minas. Publicado em: 2016-06
-
10. Identificação, mensuração e caracterização das perdas por transporte em processos construtivos
Resumo Este artigo tem como objetivo apresentar o processo de identificação, mensuração e caracterização das perdas por transporte nos fluxos físicos de processos construtivos, considerando suas incidências, tempos, causas e consequências. A abordagem metodológica adotada foi Design Science Research, desenvolvida a partir de dois estudos de caso em
Ambient. constr.. Publicado em: 2016-01
-
11. Anomalous loss hysteresis loop
This paper discusses the anomalous loss behavior in two electrical steels types. Starting from a non oriented electrical steel coil, three groups of samples with different grain sizes were produced. Grain oriented steel samples were produced from a commercially available material. The experimental procedure was performed by means of magnetic properties measu
Mat. Res.. Publicado em: 28/02/2014
-
12. Material and geometric nonlinear analysis of reinforced concrete frame structures considering the influence of shear strength complementary mechanisms
A mechanical model for the analysis of reinforced concrete frame structures based on the Finite Element Method (FEM) is proposed in this paper. The nonlinear behavior of the steel and concrete is modeled by plasticity and damage models, respectively. In addition, geometric nonlinearity is considered by an updated lagrangian description, which allows writing
Lat. Am. j. solids struct.. Publicado em: 2013-09