Strain Gauges
Mostrando 1-12 de 51 artigos, teses e dissertações.
-
1. Strain analysis in diametral compression test through digital image correlation
Abstract In the search for alternatives to obtain more information from rock tests and to make them more accessible, this study applies the Digital Image Correlation technique (DIC 2D) in a diametral compression test called Brazilian Test, comparing the result measured by an extensometer with the result obtained by DIC. Rock tests provide information about r
REM - International Engineering Journal. Publicado em: 2022
-
2. A study of strain and deformation measurement using the Arduino microcontroller and strain gauges devices
Abstract This paper presents a methodology for the measurement of strain by means of strain-gauges, where the data acquisition is done by using an Arduino Uno board, due to the low-cost and the easy manipulation of this microcontrollers. The measured signal conditioning is performed by means of a Wheatstone Bridge and then discretized by an Analog-Digital Co
Rev. Bras. Ensino Fís.. Publicado em: 10/12/2018
-
3. Dynamic crack propagation of granite subjected to biaxial confining pressure and blast loading
Abstract To great understanding the dynamic crack propagation of rock under in-situ stress and blasting, the static-dynamic loading experimental platform was built. With different confining pressure (0MPa, 2MPa, 4MPa, 6MPa, 8MPa) and different ratios (K) of horizontal-to-vertical pressure (0, 0.25, 0.5, 0.75, 1), nine texts have been carried out in quadrate
Lat. Am. j. solids struct.. Publicado em: 02/07/2018
-
4. Laboratory study of dynamic mechanical characteristic of granite subjected to confining pressure and cyclic blast loading
Abstract To investigate the deformation characteristic of deep rock under cyclic blasting, the static-dynamic loading experimental equipment was set up. The dynamic strain gauges and high-speed (HS) camera were adopted to obtain strain field and the crack propagation of rock under confining pressure of 0 MPa, 5 MPa and 10 MPa. Under the one-time loading fro
Lat. Am. j. solids struct.. Publicado em: 28/06/2018
-
5. Análise estrutural do compósito de concreto geopolimérico à base de metacaulim
Resumo O estudo de aglomerantes alternativos ao cimento Portland, como os cimentos geopoliméricos, contribui para o desenvolvimento de materiais com diferentes propriedades. Com este objetivo, nesta pesquisa, foi avaliado experimentalmente o comportamento de vigas de concreto comparando com modelo numérico utilizando Elementos Finitos. Foram fabricadas dua
Rev. IBRACON Estrut. Mater.. Publicado em: 2018-05
-
6. Effect of cantilever length and alloy framework on the stress distribution in peri-implant area of cantilevered implant-supported fixed partial dentures
ABSTRACT Because many mechanical variables are present in the oral cavity, the proper load transfer between the prosthesis and the bone is important for treatment planning and for the longevity of the implant-supported fixed partial denture. Objectives To verify the stress generated on the peri-implant area of cantilevered implant-supported fixed partial d
J. Appl. Oral Sci.. Publicado em: 2016-04
-
7. Confiabilidade e validade de um dispositivo de célula de carga para avaliação da força de preensão palmar
RESUMO A força de preensão palmar é uma medida influenciada por diversos fatores como sexo, idade, motivação, treinamento muscular, dominância, altura, peso, variáveis socioeconômicas, participação em esportes específicos ou profissões. Pode ser mensurado por meio da dinamometria ou por medidores de tensão como as células de carga (strain gauge
Fisioter. Pesqui.. Publicado em: 2015-12
-
8. Effect of veneering material on the deformation suffered by implant-supported fixed prosthesis framework
Knowing how stresses are dissipated on the fixed implant-supported complex allows adequate treatment planning and better choice of the materials used for prosthesis fabrication. Objectives: The aim of this study was to evaluate the deformation suffered by cantilevered implant-supported fixed prostheses frameworks cast in silver-palladium alloy and coated wi
J. Appl. Oral Sci.. Publicado em: 2014-06
-
9. Efeito do desajuste marginal, tipo de soldagem e material do parafuso sobre a força de destorque de parafusos protéticos e tensões induzidas aos pilares / Effect of marginal misfit, welding type and screw material on the strength of the detorque prosthetic screws and stress induced the abutments
O objetivo neste estudo foi analisar as tensões induzidas aos análogos de pilares protéticos, utilizando-se strain gauges; e avaliar a força de destorque de parafusos protéticos (ouro e titânio) em infraestruturas fundidas em titânio comercialmente puro (Ti cp), antes e após os procedimentos de soldagem laser e TIG (tungsten inert gas). Foram confecc
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 27/04/2012
-
10. Avaliação da precisão de diferentes técnicas para obtenção de modelos de trabalho de próteses implantorretidas / Evaluation of different cast techniques accuracy for implant-retained prosthesis
O intuito deste trabalho foi comparar diferentes técnicas de preenchimento do molde com gesso e verificar uma metodologia que fosse precisa o bastante para o julgamento das técnicas. Foram obtidos 40 modelos de gesso a partir de uma matriz metálica simulando uma situação clinica de prótese fixa implantorretida de três elementos. Os 40 modelos foram co
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 15/02/2012
-
11. Control of strain in a flexible beam using Ni-Ti-Cu shape memory alloy wire actuators
In this paper the development of an experimental test bench to analyze and control the strain of a flexible aluminum beam subjected to external disturbances is described. In the proposed platform, strain-gauges are used to measure the strain of the beam in a single cantilever mode while Ni-Ti-Cu Shape Memory Alloy (SMA) wires are used as force actuators. Dat
J. Braz. Soc. Mech. Sci. & Eng.. Publicado em: 2012
-
12. Desenvolvimento de uma plataforma de forças para medição e análise dos esforços verticais para modelamento biodinâmico da caminhada humana
O corpo humano pode interagir com as estruturas e estas interações são desenvolvidas através da aplicação de forças devido ao seu movimento. Uma estrutura pode sofrer alterações no seu comportamento dinâmico quando sujeita a cargas. Neste trabalho, o projeto e a construção de uma plataforma de forças é apresentado para medir as Forças de Reaç
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 2012