Thermal Cracks
Mostrando 1-12 de 41 artigos, teses e dissertações.
-
1. BACTERIAL NANOCELLULOSE BIOMEMBRANE AS A SUPPORT FOR HUMAN INSULIN AIMING AT TRANSDERMAL PERMEATION
Production of bacterial nanocellulose was pursued as a matrix system for the stabilization of human insulin. The biomembranes produced by Gluconacetobacter hansenii were washed with 2% aqueous sodium dodecylsulfate solution, rinsed with ultrapure water and immersed in 1 mol L-1 NaOH aqueous solution at 60 °C for 90 min until neutralization. For the insulin
Quím. Nova. Publicado em: 2020-05
-
2. Performance and Surface Integrity of Wire Electrical Discharge Machining of Thin Ti6al4v Plate Using Coated and Uncoated Wires
Wire Electrical Discharge Machining (WEDM) is one of the most important production technologies to manufacture very accurate small components and tools on any electrical conductive material. Titanium and its alloys have been widely used in automobile and aerospace industry as well as in medical engineering field. Small components and tools with complex geome
Mat. Res.. Publicado em: 03/06/2019
-
3. Effect of blisters and rims on radial hydride precipitation in fuel elements under dry storage conditions
ABSTRACT Hydrogen enters in Zry clads during fuel element life in service; when hydrogen exceeds the terminal solid solubility, circumferential hydrides are precipitated. In the presence of thermal gradients, produced for instance by oxide spallation, localized concentration of hydrides - known as blisters - can be formed. Due to the fact that zirconium hydr
Matéria (Rio J.). Publicado em: 19/07/2018
-
4. Impact of Alloy Composition and Thermal Stabilization on Martensitic Phase Transformation Structures in CuAlMn Shape Memory Alloys
Alloys of CuAlMn are known as cheap, high strength shape memory alloys with an excellent damping capacity within their austenitic-martensitic phase transformation, compared to alloy systems like NiTi, CuZnAl or MnCu. But CuAlMn alloys have disadvantage due to generation of voids by a high shrinkage which further increases the existing proneness to stress cra
Mat. Res.. Publicado em: 19/07/2018
-
5. Application viability evaluation of the Minimum Quantity Lubrication coolant technique under different flow rates in Plunge Cylindrical Grinding of the ABNT 4340 steel with aluminum oxide wheel
Abstract The coolant delivery technique known as Minimal Quantity Lubrication (MQL) has been employed in machining since the end of the 20th Century and has gained considerable evidence in the last years as a viable alternative to the use of the conventional coolant technique (flood). Due to the low oil flow rate delivered by the MQL technique in grinding op
REM, Int. Eng. J.. Publicado em: 2017-12
-
6. Gelatin capsule waste: new source of protein to develop a biodegradable film
Abstract This work aimed to develop biodegradable films utilizing a new source of gelatin derived from the nutraceutical capsule manufacture waste of coconut with safflower oil, coconut oil and safflower oil. The mechanical, physicochemical, barrier, optical, biodegradation, thermal and morphological properties were evaluated. All films showed low water vapo
Polímeros. Publicado em: 29/06/2017
-
7. Transient Stress Intensity Factors of Functionally Graded Hollow Cylinders with Internal Circumferential Cracks
Abstract In this paper, transient thermomechanical stress intensity factors for functionally graded cylinders with complete internal circumferential cracks are obtained using the weight function method. The finite difference method is used to calculate the time dependent temperature distribution and thermal stresses along the cylinder thickness. Furthermore,
Lat. Am. j. solids struct.. Publicado em: 2016-09
-
8. Uncracked joints in plain concrete pavements: causes, effects and possibilities of improvements
AbstractDuring the construction of Jointed Plain Concrete Pavements (JPCPs) in Chile, it was observed that joints remained uncracked. The objectives of this paper are to evaluate the effects of uncracked joints (UnCrJ) in JPCPs and to propose possible solutions or improvements to avoid or minimize this phenomenon. Considering low thermal amplitude as cause o
J. Transp. Lit.. Publicado em: 2016-03
-
9. Photodegradation of a polypropylene filled with lanthanide complexes
This research aims at studying the photodegradation of a polypropylene formulation filled with lanthanide complexes. These complexes can be used as tracers for the identification of polymer materials in order to facilitate an high speed automatic sorting of plastic wastes for an economically efficient recycling. By paying attention to the evolution of carbon
Polímeros. Publicado em: 04/12/2015
-
10. Biobased additive plasticizing Polylactic acid (PLA)
Polylactic acid (PLA) is an attractive candidate for replacing petrochemical polymers because it is from renewable resources. In this study, a specific PLA 2002D was melt-mixed with two plasticizers: triethyl citrate (TEC) and acetyl tributyl citrate (ATBC). The plasticized PLA with various concentrations were analyzed by differential scanning calorimetry (D
Polímeros. Publicado em: 2015-12
-
11. Phase Formation, Thermal Stability and Mechanical Properties of a Cu-Al-Ni-Mn Shape Memory Alloy Prepared by Selective Laser Melting
Selective laser melting (SLM) is an additive manufacturing process used to produce parts with complex geometries layer by layer. This rapid solidification method allows fabricating samples in a non-equilibrium state and with refined microstructure. In this work, this method is used to fabricate 3 mm diameter rods of a Cu-based shape memory alloy. The phase f
Mat. Res.. Publicado em: 23/10/2015
-
12. Thermal and mechanical properties of commercial MgO-C bricks
abstractMgO-C (magnesia-carbon) refractories are widely used in several steelmaking linings. These refractories are exposed to extreme stress due to high temperatures (T > 1600 °C) required to cause the metallurgical reactions. These working conditions produced refractory wear through various related processes. The different types of degradation that the ma
Matéria (Rio J.). Publicado em: 2015-09