Thermochemical
Mostrando 1-12 de 82 artigos, teses e dissertações.
-
1. A Gas Chromatography Method for Simultaneous Quantification of Inorganic Gases and Light Hydrocarbons Generated in Thermochemical Processes
This paper reports a method for simultaneous determination of H2, O2, N2, CO, CO2, CH4, C2H2, C2H4, C2H6, C3H4 (propadiene and propyne), C3H6, C3H8 and C4H10 (n-butane and isobutane) by gas chromatography using thermal conductivity and flame ionization detectors. A single porous layer open tubular column (0.53 mm internal diameter ? 30 m length ? 30 µm thic
J. Braz. Chem. Soc.. Publicado em: 2021-06
-
2. Lignocellulosic Residues from the Brazilian Juice Processing Industry as Novel Sustainable Sources for Bioenergy Production: Preliminary Assessment Using Physicochemical Characteristics
This work aims to investigate the energy-related characteristics of apple bagasse, orange bagasse and cashew-apple bagasse to identify their potential as bioenergy feedstocks. For this, a detailed characterization was performed, including proximate analysis, ultimate analysis, atomic molar ratio, heating values, chemical composition, bulk density, bioenergy
J. Braz. Chem. Soc.. Publicado em: 2020-09
-
3. Pyrolysis of the Caupi Bean Pod (Vigna unguiculata): Characterization of Biomass and Bio-Oil
The use of agricultural residues for the production of bio-oil is an important alternative to the use of fossil fuels. In this study, the Caupi bean pod (Vigna unguiculata) was characterized and used as biomass in the production of bio-oil. This biomass was evaluated in terms of physicochemical, morphological (scanning electron microscopy (SEM)), and thermal
J. Braz. Chem. Soc.. Publicado em: 2020-06
-
4. ANÁLISE GRÁFICA DO DESEMPENHO DE MÉTODOS COMPUTACIONAIS NO ESTUDO DE PROPRIEDADES TERMOQUÍMICAS
In this manuscript we have evaluated the computational methods performance in the calculation of thermochemical properties using graphical analysis. The analysis was carried out in a set of 74 organic molecules considering the following thermochemical properties: standard enthalpy of formation, ionization energy and electron and proton affinities. The evalua
Quím. Nova. Publicado em: 2020-03
-
5. Characterization of Different Surface Layers Produced by Solid Boron-Nitro-Carburizing Thermochemical Treatment on AISI 1020
The aim of this study is to obtain and characterize surface layers on low carbon steel with the pack boron-nitro-carburizing process. Different mixtures of commercial powders (Turbonit® and Ekabor®) were used to investigate the case properties, microstructure and phases formation on AISI 1020 steel. A series of experiments were conducted in solid medium wi
Mat. Res.. Publicado em: 04/11/2019
-
6. Microbial Synthesis and Characterization of Biodegradable Polyester Copolymers from Burkholderia Cepacia and Cupriavidus Necator Strains Using Crude Glycerol as Substrate
Abstract Polymers are materials of pronounced importance in the modern world, since they are massively present in everyday life, especially in the form of packaging. However, most of these materials are derived from non-renewable sources and their disposal generates large volumes of waste, which is extremely damaging to natural environments. In this context,
Braz. arch. biol. technol.. Publicado em: 24/10/2019
-
7. Nitretação por descargas elétricas da liga Ti-6Al-4V com adição de pó abrasivo SiC ao fluido dielétrico
RESUMO O processo de nitretação que usa Usinagem por Descargas Elétricas é um método que associa a capacidade de usinar superfícies complexas com a obtenção de tratamento termoquímico de nitretação. A fonte de nitrogênio é proveniente da uréia, que compõe o fluido dielétrico juntamente com água deionizada. A liga de titânio Ti-6Al-4V possui
Matéria (Rio J.). Publicado em: 16/09/2019
-
8. Effects of Gas Nitriding on Fatigue and Crack Initiation of Ti6Al4V produced by Selective Laser Melting
Selective laser melting (SLM) is an additive manufacturing technique which permits fabrication of three dimensional parts by selectively melting consecutive layers of metallic powder. This allows the production of parts with high geometrical complexity. Titanium alloy Ti-6Al-4V (Ti64) is widely used in industry due to its high strength-to-mass ratio, corrosi
Mat. Res.. Publicado em: 15/07/2019
-
9. Thermal behavior (TG-DTA-TMA), sintering and properties of a kaolinitic clay from Buenos Aires Province, Argentina
Resumo As propriedades tecnológicas de um caulim local, considerado um potencial material industrial, foram correlacionadas com o comportamento térmico e processos de sinterização realizados por meio de uma série de análises termoquímicas. A caracterização química e mineralógica do material foi realizada, juntamente com uma simples caracterizaçã
Cerâmica. Publicado em: 06/06/2019
-
10. Morphology of the DIN 100Cr6 Case Hardened Steel after Plasma Nitrocarburizing Process
Nitrocarburizing is considered one of the most important thermochemical treatments for surface modification of metallic materials and involves the simultaneous diffusion of nitrogen and carbon onto the surface. Understanding and controlling the formation of the nitrocarburized layer have considerable industrial interest due to the improvements regarding wear
Mat. Res.. Publicado em: 04/04/2019
-
11. Thermomechanical Properties of Corn Starch Based Film Reinforced with Coffee Ground Waste as Renewable Resource
Abstract Starches polymeric films offer several advantages for the replacement of synthetic polymers due to their biodegradability, non-toxicity, availability and low cost. However, the high biodegradation potential can cause fragility, considering some fundamental mechanical properties. Therefore, starch based polymeric films were reinforced incorporating l
Mat. Res.. Publicado em: 07/01/2019
-
12. A Reliable Method for Predicting the Specific Impulse of Chemical Propellants
ABSTRACT The specific impulse (Isp) is an important performance parameter that describes energy efficiency of propellant combustion and is intimately related to the rocket engine thrust. In this study, it was possible by using only two variables, i.e., the heat of reaction (Q) and the number of moles of gaseous reaction products per gram of propellant (Ng) c
J. Aerosp. Technol. Manag.. Publicado em: 16/07/2018