Two And Three Phase Flow
Mostrando 1-12 de 89 artigos, teses e dissertações.
-
1. Mancha areolada de Thanatephorus da seringueira na Amazônia: identificação filogenética e variação genética em populações do patógeno
RESUMO A mancha areolada de Thanatephorus é uma das doenças mais importantes da seringueira (Hevea brasiliensis) na Amazônia. Apesar disso, questão importante sobre o real posicionamento filogenético deste patógeno ainda não foi respondida. Neste estudo, nós analisamos os padrões de variação genética em seqüências da região ITS-5.8S do rDNA de
Summa phytopathol.. Publicado em: 14/10/2019
-
2. Atomization Characteristics of Droplet and Morphologies of Arc Sprayed Ni-Al Particles and Composition Coatings
Droplet atomization characteristics and its morphology in twin-wire arc sprayed (TWAS) Ni-Al were explored in depth. Both numerical model and theoretical method were built for calculating the process of the droplet deformation and breakup in air flow, which based on the standard k-ε model and the volume of fluid (VOF) dual-phase flow model. The atomization
Mat. Res.. Publicado em: 23/09/2019
-
3. Thermal profiles in pervious concrete during summer rain simulations
ABSTRACT Pervious concrete pavement systems may have many environmental benefits including the mitigation of heat island impacts. This mitigation is a complex combination of pervious concrete’s insulating capability and its ability to store water which may provide evaporative cooling. However, the introduction of water may also bring heat into the system,
Matéria (Rio J.). Publicado em: 18/10/2018
-
4. Nutrient Biological Removal in an Up-flow Sludge Bed Reactor under Intermittent Aeration using Glycerol as the Sole Carbon Source
Abstract This work evaluated the feasibility of glycerol as the sole carbon source for nutrient biological removal in an intermittently aerated bioreactor. The reactor operation was divided into two phases: the first one aimed only at removing nitrogen; and the second one aimed at removing nitrogen and phosphorus. In the first operational phase, three C/N (C
Braz. J. Chem. Eng.. Publicado em: 2017-10
-
5. CONTINUOUS AND SEMICONTINUOUS REACTION SYSTEMS FOR HIGH-SOLIDS ENZYMATIC HYDROLYSIS OF LIGNOCELLULOSICS
Abstract An attractive operation strategy for the enzymatic hydrolysis of lignocellulosics results from dividing the process into three stages with complementary goals: continuous enzyme adsorption at low-solids loading (5% w/w) with recycling of the liquid phase; continuous liquefaction at high-solids content (up to 20% w/w); and, finally, continuous or sem
Braz. J. Chem. Eng.. Publicado em: 2015-12
-
6. Numerical Simulation of the Wake Structure and Thrust/Lift Generation of a Pitching Airfoil at Low Reynolds Number Via an Immersed Boundary Method
ABSTRACT: In this study, an accurate computational algorithm in the context of immersed boundary methods is developed and used to analyze an incompressible flow around a pitching symmetric airfoil at Reynolds number (Re = 255). The boundary conditions are accurately implemented by an iterative procedure applied at each time step, and the pressure is also upd
J. Aerosp. Technol. Manag.. Publicado em: 2015-09
-
7. Simulation of the solidification in a channel of a water-cooled glass flow
A computer simulation study of a laminar steady-state glass flow that exits from a channel cooled with water is reported. The simulations are carried out in a two-dimensional, Cartesian channel with a backward-facing step for three different angles of the step and different glass outflow velocities. We studied the interaction of the fluid dynamics, phase cha
Braz. J. Chem. Eng.. Publicado em: 2014-12
-
8. CFD and experimental investigation on the heat transfer characteristics of alumina nanofluids under the laminar flow regime
This study reports experimental and Computational Fluid Dynamics (CFD) investigations of the laminar convective heat transfer coefficient of Al2O3/water nanofluids in a circular tube under uniform and constant heat flux on the wall. Three different models including a constant physical properties single-phase (CP-SP) model, a variable physical properties sing
Braz. J. Chem. Eng.. Publicado em: 2014-06
-
9. The 3D CFD study of gliding swimmer on passive hydrodynamics drag
The aim of this study was to analyze the effect of depth on the hydrodynamic drag coefficient during the passive underwater gliding after the starts and turns. The swimmer hydrodynamics performance was studied by the application of computational fluid dynamics (CFD) method. The steady-state CFD simulations were performed by the application of k - omega turbu
Braz. arch. biol. technol.. Publicado em: 2014-04
-
10. Mathematical modeling of supercritical fluid extraction of oil from canola and sesame seeds
Mathematical modeling of supercritical fluid extraction of oil from canola and sesame seeds with a two-phase model was performed in this work. A model based on differential mass balance was used to correlate the experimental data. Different adsorption isotherm models (Henry, Freundlich and Brunauer, Emmet and Teller (BET)) were used to describe the equilibri
Braz. J. Chem. Eng.. Publicado em: 2013-03
-
11. Metodologia para aplicar LES ao craqueamento catalítico fluido em um reator riser industrial / Large eddy simulation application methodology to a fluid catalytic cracking industry reactor
The main objective of this thesis is to propose a methodology in how to apply Large Eddy Simulation (LES) on a unit of catalytic cracking. In order to achieve this, it was proposed an alternative way of constructing the computational mesh, by using quasi-uniform meshes. The proposed meshes were implemented to minimize the computational effort and procedure f
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 14/09/2012
-
12. Influência da geometria da nanocarga na estruturação, orientação e propriedades de filmes tubulares de nanocompósitos de PA6 / Influence of the nanoparticles shape on the structure, orientation and properties of pa6 nanocomposites blown films
The structure and morphology of polymers and consequently their properties are dependent on the processing conditions. During the blown film process, high shear and elongational flows can induce a preferred orientation of the polymer chains; controlling the process conditions, it is possible to obtain films with anisotropic properties. Polymeric nanocomposit
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 13/06/2012