Work Uniform
Mostrando 1-12 de 288 artigos, teses e dissertações.
-
1. Morphology Behavior of Copper Films Deposited after Wet Surface Treatment on Polished Alumina
In this paper, a pre-treatment process for electroless copper (Cu) deposition on the polished alumina (Al2O3) 99.9% and the behavior of Cu plating by electroless process after Al2O3 surface treatment were explored. Our work was carried out by changing the roughness of Al2O3 through micro-etching (coarsening), nucleation its surface by a two-step method (sens
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
2. Designing and fabrication of a low-cost dip-coater for rapid production of uniform thin films
In this work, a self-made dip-coater equipment was developed for the fabrication of thin films. The assembly of the apparatus was carried out using simple mechanical and electronic pieces, recycle parts, and spending an inexpensive budget suitably. The production, software design, and features of the device were focused on the sol-gel dip-coating method, whi
Química Nova. Publicado em: 2022
-
3. Effect of Multi-Pass Rolling on the Performance of AZ31 Magnesium Alloy Anode in Mg-Air Battery
In this work, the influence of rolling passes on microstructure, corrosion behavior, electrochemical performance, and battery performance of AZ31 magnesium alloy was studied. The experimental results show that the grain size decreases first and then increases with rolling passes. Among them, the grain size of three passes rolled sample is the smallest, while
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
4. ASYMMETRIC WETTED SECTOR ANGLE IN WATER DISTRIBUTION OF TRAVELING GUN IRRIGATION SYSTEMS
ABSTRACT This work aimed to simulate the water distribution of traveler gun irrigation, working with asymmetrical wetted angles and in windy conditions. In the simulations of a sprinkler with uniform radial profile, the following were considered: i) wetted angles between 180 and 330°; ii) wetted angle asymmetries from 0 to 90°; iii) wind speeds from 0 to 4
Eng. Agríc.. Publicado em: 2020-08
-
5. Imaging evaluation of hallux valgus
Abstract This work investigates an alternative numerical scheme for the solution of an exact formulation based on Geometrical Optics (GO) principles to synthesize offset dual reflector antennas. The technique is suited to solve a second-order nonlinear partial differential equation of the Monge-Ampère type as a boundary value problem. An iterative algorithm
Radiol Bras. Publicado em: 2020-06
-
6. GO Synthesis of Offset Dual Reflector Antennas Using Local Axis-Displaced Confocal Quadrics
Abstract This work investigates an alternative numerical scheme for the solution of an exact formulation based on Geometrical Optics (GO) principles to synthesize offset dual reflector antennas. The technique is suited to solve a second-order nonlinear partial differential equation of the Monge-Ampère type as a boundary value problem. An iterative algorithm
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2020-06
-
7. Comportamento da função renal na crioablação percutânea de massa renal
Abstract This work investigates an alternative numerical scheme for the solution of an exact formulation based on Geometrical Optics (GO) principles to synthesize offset dual reflector antennas. The technique is suited to solve a second-order nonlinear partial differential equation of the Monge-Ampère type as a boundary value problem. An iterative algorithm
Radiol Bras. Publicado em: 2020-06
-
8. Hidrodissecção modificada para biópsia guiada por tomografia computadorizada de lesões mediastinais: técnica “marshmallow”
Abstract This work investigates an alternative numerical scheme for the solution of an exact formulation based on Geometrical Optics (GO) principles to synthesize offset dual reflector antennas. The technique is suited to solve a second-order nonlinear partial differential equation of the Monge-Ampère type as a boundary value problem. An iterative algorithm
Radiol Bras. Publicado em: 2020-06
-
9. Reliability-based calibration of Brazilian structural design codes used in the design of concrete structures
Resumo Este artigo apresenta a calibração, baseada em confiabilidade, dos coeficientes parciais de segurança das normas brasileiras utilizadas no dimensionamento de estruturas de concreto. O trabalho está fundamentado na teoria de confiabilidade, que permite uma representação explícita das incertezas envolvidas em termos das resistências e ações. N
Rev. IBRACON Estrut. Mater.. Publicado em: 13/12/2019
-
10. AVALIAÇÃO DE DIFERENTES CULTURAS STARTERS NA ELABORAÇÃO DE SALAME TIPO ITALIANO
Resumo O Salame Tipo Italiano produzido no Brasil é predominantemente obtido de carne suína, com maturação aproximada de 30 dias, atingindo pH em torno de 5,4. O uso das bactérias do gênero Lactobacillus como culturas iniciadoras propicia o processo de fermentação e a obtenção de produtos uniformes e seguros, com redução do tempo de maturação d
Ciênc. anim. bras.. Publicado em: 13/12/2019
-
11. Contributions of the High Frequency Dynamic Wire Feeding in the GTAW Process for Increased Robustness
Abstract: The GTAW process is recognized as a process of high metallurgical quality, being widely used in the pipelines welding, mainly in the root pass. The relative independence between the heat delivered to the melting pool and the amount of material added helps to control the melting of the material and to avoid the appearance of welding discontinuities
Soldag. insp.. Publicado em: 02/12/2019
-
12. Analysis of the Dynamic Stability of Ball-End Milling of AISI D6 Hardened Steel
AISI D6 hardened steel is a difficult to cut material that it is employed in mould and die manufacturing where long ball-end mills are frequently required to machine deep cavities. This condition can lead to excessive vibration between tool and workpiece resulting in a poor surface finishing and reduced tool life. This work analyses the dynamic stability of
Mat. Res.. Publicado em: 02/12/2019